The Ecovacs T8 falls into a rare class that uses a laser and front camera. It navigates like a LIDAR-based robot, but the front camera helps it avoid obstacles. This model is the first of its kind, and in this review we will find out how well it avoids obstacles.
How good are the Ecovacs T8 at avoiding obstacles?
Ecovacs T8 AIVI Review
One of the interesting features of the Ecovacs T8 AIVI is front cameraand enable it Avoid obstacles. But how good is this sensor at doing that? I’ve done extensive testing, and you can avoid certain things. Avoids stool if approached directly. However, if he fell into a blind area, he would not avoid him. So the technology is not perfect. Cleaning performance is decent, especially with the presence of surface debris. The higher cost should give you pause, as the Roborock S6 MaxV offers better obstacle avoidance and a better deep cleaning.
* If you click on this link and make a purchase, we earn a commission at no additional cost to you.
- Excellent airflow At more than 23 feet per minute
- Highly usable power even on the lowest setting
- side-less design From Roborock S6 MaxVso it can be placed under furniture With an area of 3.7″ and less
- Three hours running time
- on 65 dB in the highest place
- Average in deep carpet cleaning
- Navigation is not as efficient as Roborock
- It only saves up to two maps
Introduction to Ecovacs T8 AIVI
T8 AIVI is the first Ecovacs robot with a front camera. AIVI stands for artificial intelligence, vision, enabling it to detect and avoid obstacles. So the question is, how well do you work?
The T8 has undergone a range of tests with various drawbacks, and I will reveal the results below.
There are two Ecovacs T8 options.
The first is T8 AIVI with front camera. This alternative is currently DEEBOT’s main choice.
We earn a commission if you click on this link and make a purchase at no additional cost to you.
Next up is the T8 (without AI software) with three laser sensors on the front for obstacle detection.
Like all Ecovacs robots, the T8 has a round frame with a matte charcoal coating that I like because it resists scratches better.
Trash is loaded from the top and Capacity 0.42ml. So it is slightly smaller than the Roborock S4 Max.
It has a 240ml rear-loading water tank. Unfortunately, the scanning bracket does not slide from the back. You’ll have to flip the robot over or remove the water tank to install it, which is an extra step.
At the bottom, the T8 has a dual side brush system that surrounds the brush combo.
The brush is narrow, measuring less than 7 in width, but it has a good enough seal to pick up debris even on the lowest setting.
The T8 relies on the Laser Sensor (or LIDAR) as the primary navigational instrument. The laser is completely accurate with location tracking. This bot rarely does not find the main base – even in complex layouts.
It closely resembles Roborock and Neato, but lags a bit when it comes to efficiency.
Like those brands, the T8 starts cleaning the edges before moving toward the middle.
However, the similarity ends here. Unlike Roborock and Neato which can spin up to three times, the T8 can only do it twice.
This shouldn’t be much of an issue for everyday cleaning tasks, but I’d rather have the option of getting an extra pass.
I tested how well the T8 performed in a coverage test. In this experiment, I scattered Quaker oats around a test area to see how much they pick up.
The T8 was decent, capturing just about everything after running it twice. Completed the task in 11 minutes, which is pretty fast despite not using the most efficient path.
However, I feel the T8 lags a bit behind Roborock when cleaning up more complex layouts.
This robot is compatible with the Ecovacs application. Look for “Ecovacs” wherever you download your apps to access them.
I have tested the app extensively, and it offers a lot in terms of features, which I will summarize in this section.
The app has a live map that provides users with real-time information on the bot’s location, area size, and battery level.
It can also detect the correct map level after the initial scan. So there is no need to select the map manually.
Selective room cleaning
At the bottom left of the map, you’ll see the Region tab. This section allows you to select an area to clean by clicking on a specific room.
Please note that you will need to save the map first and then manually split each section for this function to work.
It has a similar spot cleaning function, but is more accurate as users can determine exactly where the robot is cleaning without having to carry the robot.
The app also enables you to select the area to be cleaned first. Tap the Cleaning Sequence tab at the bottom left of the screen, then change the order in which the room goes first.
This section allows users to select power and water level modes. There are four options for each. Users can also set the number of passes – one or two.
Save the map
You can technically save up to two map levels, but it is possible to add a third map, but the app will not allow users to save it.
Simply move the bot to the 3rd floor level and turn it on, and it will create the new map.
After the floor plan of the new building is created, the application automatically divides the area into sections. The algorithm isn’t perfect, so you might want to redo the partitions by merging spaces first and then splitting them.
After the partitions are divided, users can proceed to naming the rooms. Unfortunately, the app allows users to choose from a list. The custom label is not available, so you have to content yourself with the list.
Another useful aspect of the T8 is the containment features. The Ecovacs app offers three ways to block restricted areas – invisible wall, mop-free areas, and virtual boundaries.
- invisible wall They are virtual lines that prevent the robot from bypassing them.
- No-mop areas: Prevents the robot from entering a square or rectangular area
- Default limits: Similar to the no-wipe zone functions
Displays the history of previous cleaning cycles, along with the corresponding maps, the total number of cleaning cycles, and the area covered.
Shows users a snapshot of how much they use the bot.
automatic batch suction
Similar to the carpet boost feature, the robot vacuum automatically increases suction when it detects carpet.
The Ecovacs app supports unlimited scheduling. You can run an unlimited number per day, as needed, at different times.
There are three different options.
- Automatic cleaning: Directs the robot to clean the entire floor level
- Area cleaning: Tells the robot to clean a specific area.
- Scheduling a home periodical: The robot will walk around the house and provide snapshots of what the camera sees
It works in conjunction with the Ecovacs T8’s automatic emptying station. You can buy this separately.
We earn a commission if you click on this link and make a purchase at no additional cost to you.
How much power does the Ecovacs T8 AIVI have?
One of the surprises of this product is the airflow. I used an anemometer to check, and here are the results.
- calm: 8.2 CFM
- Basic: 22.58 cubic feet per minute
- the above: 22.93 cubic feet per minute
- Max +: 23.1 cubic feet per minute
Ecovacs says the lowest setting is about mopping, but it has usable power, at least for hard surfaces.
The standard difference, max, and max + airflow are very close, and the difference is minimal.
You can leave it on the standard setting with the Carpet Boost feature to automatically increase suction if it detects a carpet.
I tested T8 on various debris such as hair, Quaker oats, quinoa, sand, coffee grounds, pet droppings, Cheerios, and more. It is a comprehensive test to see how well and how well it is tolerated.
First, here are the overall results.
- Total: 90.11%
- Solid ground: 98.15%
- Carpet (surface): 97.72%
- deep cleaning: 66.65%
- Sand on the hard floor: 99%
Tests reveal a few things about the Ecovacs T8. First, it is excellent at picking up surface debris on hard floors and carpets. Second, it tends to struggle with fine things like ground coffee on the carpet but it works well on carpet.
Third, the double-sided brush system will scatter large clumps of debris like quinoa oats and Quaker oats – one reason they’re below 99%.
hard floor results
- Quaker Oats: 98.2%
- Cafe floors: 99.6%
- Quinoa: 96.8%
- pet litter: 98%
Despite the initial distraction, T8 captured most of the Quaker oats in subsequent passes. Did not do well with quinoa as the spread was more widespread and therefore the result was lower.
Picking is not a problem on hardwood floors; Scattering the side brush may hinder its performance, but it should not be a concern for everyday tasks.
sand on hard floor
The sunflower test of any robotic vacuum cleaner is cleaning sand on hard floors. I tested the T8 on 50g of sand, and there it is picked up an average of 99%. Not as good as Roborock S4 Max And Roomba 980but it’s still at the top level of the robot vacuum I tested.
One of the reasons for the drop in points is the two-sided sand brush.
It has a good enough sealant and agitation to pick up sand even in the slightest, getting a score of 98.7%.
On the max + setting, the result increased to 99.3%.
One benefit of having two side brushes is that it cleans edges better. That was the case with the ILIFE A10 I covered earlier, and it’s the same for the Ecovacs T8.
Check out the before and after picture.
It didn’t pick up everything, only a few parts remained on the sidelines, but it’s impressive for a round-shaped robot vacuum.
Low stack results
- Quaker Oats: 100%
- Cafe floors: 96.8%
- Quinoa: 100%
- pet litter: 99%
Surprisingly, the T8 performed best on low-pile carpets with two grades of 100%. Spreading side brush debris is not much of an issue on this surface because there is more friction.
- Quaker Oats: 99.4%
- Cafe floors: 87.6%
- Quinoa: 100%
- pet litter: 99%
T8 struggles more with ground coffee because the finer bristles don’t have enough agitation to pick up small particles of dirt.
It’s the same problem when cleaning inline sand on a medium pile rug, which I will discuss in the next section.
For other debris like Quaker oats and pet droppings, that was excellent.
Next, we’ll take a look at how well the Ecovacs T8 performs in compact sand. I rubbed 100g worth of 100gm on a medium pile rug.
I picked up average 66.65% In two tests, which is disappointing given the higher airflow.
This result is just average for a robot vacuum but lower than other brands in its price range, such as Roborock S6 Max V And Neato D7.
hair wrap test
Another experiment I did was to test curling the hair with one gram of five and seven inches of hair strand.
Here are the results.
- 5 grams of hair strands:37 grams (or 37%) inside the dustbin, and 0.63 grams (or 63%) inside the dustbin.
- 7 grams of hair strands:37 grams (or 37%) inside the dustbin, and 0.63 grams (or 63%) inside the dustbin.
These are frustrating results with the high airflow in the T8.
But the soft bristles and lack of an anti-tangle system play one of the factors that cause a high percentage of hair to wrap around the brush.
The Ecovacs T8 AIVI, like the Roborock S6 MaxV, has a 230ml electronic water tank. Unfortunately, the wipe pad doesn’t slide out from the back, so you’ll have to flip the robot over or remove the water tank to install it.
I tested it on red wine stains that I dried overnight, and here is a before and after photo.
For this experiment, I used the third highest flow setting. While it cleaned most stains, it left noticeable residue and marks in the tires.
I made a second pass, and I could still see the remains. It’s far behind other robot vacuums I’ve tested, including the Dreame D9, Roborock S5 Max, S6 MaxV, and Viomi V3.
How Noisy is the Ecovacs T8 AIVI?
To check for noise, I use a sound meter to record sound at all power levels.
- calm: 58.2 dB
- Basic: 61 dB
- the above: 66.6 dB
- Max +: 67.1 dB
T8 docile in Quiet or Standard modeAnd I used it at night while my son was watching Netflix, and it didn’t seem to bother him.
However, the sound gets louder when going to max and max +, Breaking the 65 decibel barrierwhich can only be used during the day.
How long does the Ecovacs T8 AIVI last?
T8 AIVI uses file Li-ion battery with a capacity of 5200 mAh And they will nominate for up to 180 minutes in standard mode. There is plenty of usable airflow in this setup, so this robot is a good option even inside large homes.
It recharged and resumed, so it resumes cleaning if it didn’t finish the job and goes back to where it left earlier. You can turn this feature on or off in the app.
What comes in the box?
- Ecovacs T8 AIVI Robot Vacuum Cleaner
- Extra pair of side brushes
- Wipe backing plus 1 microfiber pad
- Charging base with plug
- Extra HEPA filter
- User’s Manual
Parts of the Ecovacs T8 are readily available at stores such as Amazon. You will have several options for things like filter, side brush, and main brush. Packages are available for those looking to stock up on spare parts. It’s an excellent way to save money, as bundles are usually cheaper than buying a single piece.
Robotic vacuums need TLC to keep them running at their peak. T8 AIVI is no exception. I will list the parts that will need to be replaced or cleaned.
- Basic brush: This component takes the most abuse because it is responsible for capturing debris. Check and clean it at least once a week and remove any hair or debris stuck on it.
- Side brushes: The hair will wrap around the base of the side brush. Remove this buildup to prevent unnecessary friction and premature wear with the engine. Unplug and wipe with a slightly dampened microfiber towel once a month.
- Dustbin and filter: Empty the trash at each cleaning cycle if possible to avoid spillage. Check the filter and tap it against a hard object such as a trash can to remove any dirt stuck to the creases. The middle filter and mesh filter inside the litter box are washable.
- front camera: Use a clean microfiber towel to wipe the front camera.
- laser sensor: One of the tools I use to clean the LIDAR sensor is a vacuum cleaner with the included brush. Avoid pricking a hard object as it will damage or misalign it.
- fall sensors: There are six drop sensors underneath the T8. Use a clean, dry towel to wipe it once a month. Dirt will build up and cause error codes if left unclean.
- Wheels: Wipe the wheel and side wheels with a clean microfiber towel.
|Model||Ecovacs T8 AIVI|
|Battery||5200 mAh Li-ion|
|Run time||Up to 180 mins.|
|Water Tank Capacity||230 ml|
|Dirt Capacity (dry)||420 ml.|
|Recharge and Resume||Yes|
Where can I buy Ecovacs T8 AIVI?
You can buy T8 AIVI from online stores such as Amazon. Check out the links below for more information on the latest prices.
Note that there are two variants of the T8 on Amazon – the AIVI (with the front camera) and the T8 (with the three front laser sensors). The latter is cheaper, but I haven’t tested it yet – I can’t comment on its performance.
Disclaimer: I’ll earn a commission if you buy through any of the links above, but at no additional cost to you, so it’s a win for us!
Does Ecovacs T8 AIVI Offer Excellent Value?
I was expecting a lot from this robot vacuum because it is so expensive. Despite its overall good performance, it fell behind the Roborock S6 MaxV in several areas, namely, deep cleaning performance and snag avoidance.
The front camera does its job and will avoid objects if you approach it at the right angle. Otherwise, it will fall into a blind area and the robot will not escape from it.
Cleaning performance is very good, especially on surface dirt. But it is average in cleaning compact sand with an average of 66.65%. Decent, but not something to rely on to deep clean carpets.
The wiping is another disappointment because it left visible residue and frame marks. It lags behind other premium brands like RoborockAnd Fayoumi and Dream in this area.
Verdict: Good option but the high cost gives me pause
While the Ecovacs DEEBOT T8 AIVI is an excellent robot vacuum for Vacuum floors for efficient mobilityThe obstacle avoidance and scanning system are a bit laggy.
It doesn’t fully “see” and has blind spots, so you can’t rely on this bot to avoid things on its own.
If it approaches an object at the right angle, it will avoid it, but otherwise, it will make contact. If you have pets, be sure to remove their faeces or else cleaning will be tedious.
Between the T8 AIVI and the Roborock S6 MaxV, I’d go with the latter as it has better snag avoidance, deep cleaning, and better mops.
One of the advantages that the T8 has over the S6 MaxV is the availability of a file Pavement that empties automatically collects debris from the trash.
Reason to buy Ecovacs T8 AIVi
- obstacle avoidance: The front camera on the T8 AIVI is good at avoiding obstacles. Despite the blind spots, it’s an extra layer of technology that helps this robot avoid things.
- high air flow: This robot has 23 CFM in Roomba area.
- Intelligent navigation: The laser sensor and SLAM enable this robot to navigate efficiently. It is able to navigate even in confined spaces without getting stuck.
- Excellent on hard floors: The T8’s high airflow translates well into cleaning hard floors.
It looks promising but lags behind the Roborock S6 MaxV with snag avoidance and cleaning performance
- Mobility – 95%
- Surface cleaning – 98.29%
- deep cleaning – 66.65%
- Quality – 94%
- Design – 95%
- Values - 92%
- TOTALE AVERAGE: 90%
The Ecovacs T8 AIVI looks promising on paper with its front camera and AI technology. While it can avoid things, the camera has blind spots, so you can’t just rely on it to evade these things. Cleaning performance is good, especially surface debris, but it’s not as good as the S6 MaxV with its built-in dirt cleaning score of only 66.65%. The high price tag gives me pause to totally recommend this option, but it’s a convenient alternative if you need the auto-discharge feature not available with the S6 MaxV.